TARIFF CONCESSION REVOCATION ORDER Under Section 269SD(2) of the Customs Act 1901, I Robert Crawford a delegate of the Chief Executive Officer (a) revoke Tariff Concession Order Number 9708969 made on 05.01.98, in respect of the goods described in TABLE A below. This Revocation has effect from 01.01.07; and (b) make in its place the Tariff Concession Orders described in TABLE B. The goods specified in Column 1 of TABLE B are goods to which the item in Part III of Schedule 4 to the Customs Tariff Act 1995 specified in Column 2 of TABLE B applies. The Order shall have effect from the date notified in paragraph (a) above as the date of effect for the Revocation. TABLE A COLUMN 1 COLUMN 2 Description of Goods including the Schedule 4 Item Number Last date of effect Customs Tariff Classification 8708.99.99 PARTS, SUSPENSION, COMMERCIAL MOTOR VEHICLE, being ANY of the 50 following: 31.12.06 (a) spring hangers or frame shockhangers having: (i) a minimum yield strength of 380 mPa; (ii) a minimum tensile strength of 550 mPa; (iii) a minimum elongation of 6%; (iv) a general hardness range of 187-255 BHN; (v) attachment load capacity NOT exceeding 60 kN; (b) torque rods or transverse rods having: (i) 3 axis with end joint connections of either taper pin or bar pin; (ii) an attachment tensile and compressive load capacity NOT exceeding 35 kN; (c) top pads or transverse rod frame brackets having: (i) minimum yield strength of 300 mPa; (ii) minimum tensile strength of 450 mPa; (iii) minimum elongation of 12%; (iv) a general hardness range of 156-217 BHN; (d) spring seats or axle bottom caps having: (i) minimum yield strength of 380 mPa; (ii) minimum tensile strength of 550 mPa; (iii) minimum elongation of 6%; (iv) general hardness range of 187-255 BHN; (v) attachment load capacity NOT exceeding 35 kN; (e) transverse rod axle brackets having: (i) minimum yield strength of 300 mPa; (ii) minimum tensile strength of 550 mPa; (iii) minimum elongation of 20%; (iv) a general hardness range of 156-196 BHN; (f) cross channels or lower shock brackets having: (i) minimum tensile strength of 448 mPa; (ii) minimum yield strength of 350 mPa Op. 10.10.97 - TC 9708969 This is page 1 of 2 Pages of the instrument. ..Robert Crawford...................... Dated 20 June 2007 Delegate of the Chief Executive Officer Revocation Instrument HS2007/578A TABLE B COLUMN 1 COLUMN 2 Description of Goods including the Schedule 4 Item Number Last date of effect Customs Tariff Classification 8708.80.99 PARTS, SUSPENSION, COMMERCIAL MOTOR VEHICLE, being ANY of the 50 following: (a) spring hangers or frame shockhangers having: (i) a minimum yield strength of 380 mPa; (ii) a minimum tensile strength of 550 mPa; (iii) a minimum elongation of 6%; (iv) a general hardness range of 187-255 BHN; (v) attachment load capacity NOT exceeding 60 kN; (b) torque rods or transverse rods having: (i) 3 axis with end joint connections of either taper pin or bar pin; (ii) an attachment tensile and compressive load capacity NOT exceeding 35 kN; (c) top pads or transverse rod frame brackets having: (i) minimum yield strength of 300 mPa; (ii) minimum tensile strength of 450 mPa; (iii) minimum elongation of 12%; (iv) a general hardness range of 156-217 BHN; (d) spring seats or axle bottom caps having: (i) minimum yield strength of 380 mPa; (ii) minimum tensile strength of 550 mPa; (iii) minimum elongation of 6%; (iv) general hardness range of 187-255 BHN; (v) attachment load capacity NOT exceeding 35 kN; (e) transverse rod axle brackets having: (i) minimum yield strength of 300 mPa; (ii) minimum tensile strength of 550 mPa; (iii) minimum elongation of 20%; (iv) a general hardness range of 156-196 BHN; (f) cross channels or lower shock brackets having: (i) minimum tensile strength of 448 mPa; (ii) minimum yield strength of 350 mPa Op. 01.01.07 - TC 0614566 This is page 2 of 2 Pages of the instrument. ..Robert Crawford...................... Dated 20 June 2007 Delegate of the Chief Executive Officer Revocation Instrument HS2007/578A