AIRWORTHINESS DIRECTIVE On the effective date specified below, and for the reasons set out in the background section, the CASA delegate whose signature appears below revokes Airworthiness Directive (AD) AD/BELL 206/167 Amdt 2 and issues the following AD under subregulation 39.001(1) of CASR 1998. The AD requires that the action set out in the requirement section (being action that the delegate considers necessary to correct the unsafe condition) be taken in relation to the aircraft or aeronautical product mentioned in the applicability section: (a) in the circumstances mentioned in the requirement section; and (b) in accordance with the instructions set out in the requirement section; and (c) at the time mentioned in the compliance section. Bell Helicopter Textron Canada (BHTC) 206 and Agusta Bell 206 Series Helicopters AD/BELL 206/167 Amdt 3 Transmission Pylon Support Spindle 12/2007 DM Applicability: Bell Model 206 A and B series helicopters, and Agusta Model AB 206 A and B series helicopters; that have the following part number 206-031-554 Transmission Pylon Support Spindle (Spindle) serial numbers, installed: Spindles repaired by Cadorath Aerospace Inc., B12-11568, B12-12244, B12-12260, B12-12647, B12-12676, B12-12847, B12-13292, B12-14395, B12-15750, B12-17149, B12-17266, B12-1828, B12-18649, B12-19330, B12-19381, B12-20668, B12-2224, B12-2286, B12-3595, B12-3774, B12-3808, B12-5171, B12-757, B12-8053, B12-8605, B12-932, B-21223, B-21297, B22005, B22515, B-22558, CAI3852, CAI3853, EA287, EA318, EA322, EA393, EA751, EA761, MW546, RE1044, RE113, RE743. Spindles repaired by H-S Tools & Parts Inc., B12-11127, B12-12883, B12-13158, B12-13535, B12-13545, B12-13593, B12-13657, B12-13716, B12-14061, B12-14078, B12-15131, B12-15908, B12-16078, B12-16267, B12-16825, B12-16867, B12-17149, B12-17266, B12-18157, B12-18163, B12-18456, B12-19450, B12-21573, B12-3106, B12-605, B12-7627, B-22385, EA-391, MW445, MW506, MW546, RE278, RE329, RE852. Requirement: Check the technical logbook entries to determine if a Spindle part number 206-031-554 with a serial number listed in the Applicability section above is installed on the helicopter. If an affected Spindle is installed, before further flight, replace the Spindle with a serviceable part. Note: Transport Canada AD CF-2007-02R1, EASA ADs 2007-0257 and 2007-0089, refer. Compliance: Within 16 flight hours after 25 September 2007, but no later than 15 October 2007; unless already accomplished. This Amendment becomes effective on 25 September 2007. Background: A Transportation Safety Board of Canada investigation into an accident has revealed that the Spindle repaired by Cadorath Aerospace Inc., failed during flight and resulted in loss of control of the helicopter. This Directive requires removal of all Spindles repaired by Cadorath Aerospace Inc. Amendment 1 required the same technical actions as the original issue of this Directive to be applied to Agusta Model 206 A and B series helicopters. Amendment 2 corrected the text of the compliance statement for Model AB 206 helicopters, with no change to the compliance time. Amendment 3 is issued in response to a revision of the related Transport Canada AD and a new EASA AD, which include Spindles repaired by HS Tools & Parts Inc. to the applicability. David Villiers Delegate of the Civil Aviation Safety Authority 20 September 2007