Vehicle Standard (Australian Design Rule 60/00 – Centre High Mounted Stop Lamp) 2006 Made under section 12 of the Road Vehicle Standards Act 2018 Compilation: 1 (up to and including Vehicle Standard (Australian Design Rule) Lighting Standards Amendment Instrument 2022 (No.1) Compilation Date: 20 January 2023 Compiled by: Vehicle Safety Policy and Partnerships, Department of Infrastructure, Transport, Regional Development, Communications and the Arts CONTENTS A. legislative provisions.............................................3 B. function and SCOPE.............................................3 C. APPLICABILITY AND IMPLEMENTATION........................3 60.1. DEFINITIONS..................................................4 PART I PHOTOMETRIC REQUIREMENTS................................4 60.2. SPECIFICATION...............................................4 60.3. LIGHT TABLES................................................5 PART II INSTALLATION...............................................6 60.4. SPECIFICATION...............................................6 60.5. ALTERNATIVE STANDARDS....................................6 COMPILATION NOTES................................................7 1. legislative provisions 1. NAME OF STANDARD 1. This Standard is the Vehicle Standard (Australian Design Rule 60/00 – Centre High Mounted Stop Lamp) 2006. 2. This Standard may also be cited as Australian Design Rule 60/00 — Centre High Mounted Stop Lamp. 2. function and SCOPE The function of this Australian Design Rule is to specify requirements for a supplementary 'Centre High-mounted Stop Lamp' on the rear of the vehicle, to provide an additional indication to other road users to the rear of the vehicle that the driver of the vehicle is applying the service brakes. C. APPLICABILITY AND IMPLEMENTATION C.1. Applicability Summary C.1.1. This ADR applies to the design and construction of vehicles as set out in the table below. C.1.2. Those vehicles must be equipped with a 'Centre High-mounted Stop Lamp' complying with the relevant requirements of this National Standard. C.1.3. Vehicles complying with the requirements for S3 category stop lamps in ADR 49/00, installed in accordance with the requirements for S3 category stop lamps in ADR 13/00 need not comply with this national standard. C.2. Applicability Table Vehicle Category ADR Category Code [*] UN Category Code * Manufactured on or After Acceptable Prior Rules Moped 2 wheels LA L1 Not Applicable Moped 3 wheels LB L2 Not Applicable Motor cycle LC L3 Not Applicable Motor cycle and sidecar LD L4 Not Applicable Motor tricycle LE L5 LEM Not Applicable enclosed vehicles LEP 1 March 1991 Nil all vehicles LEP 1 July 1992 Nil LEG Not Applicable Passenger car MA M1 1 July 1989 Nil Forward-control passenger vehicle MB M1 1 July 1996 Nil Off-road passenger vehicle MC M1 1 July 1996 Nil Light omnibus MD M2 Not Applicable Heavy omnibus ME M3 Not Applicable Light goods vehicle NA N1 Not Applicable Medium goods vehicle NB N2 Not Applicable Heavy goods vehicle NC N3 Not Applicable Very light trailer TA O1 Not Applicable Light trailer TB O2 Not Applicable Medium trailer TC O3 Not Applicable Heavy trailer TD O4 Not Applicable 60.1. DEFINITIONS 60.1.1. Refer to Vehicle Standard (Australian Design Rule Definitions and Vehicle Categories) 2005. PART I PHOTOMETRIC REQUIREMENTS 60.2. SPECIFICATION 60.2.1. Colour of light emitted: Red to SAE document J578c, February, 1977 "Color Specification for Electric Signal Lighting Devices", or as specified in clause 60.3.2. 60.2.2. Intensity of light emitted 60.2.2.1. Minimum: In each direction corresponding to the points in the light distribution table of clause 60.3.1, the luminous intensity must be not less than the figure specified in the table for the direction in question. 60.2.2.2. Maximum: 160 cd in any direction. The luminous intensity must not exceed this maximum over an area larger than that generated by a 0.25o radius within a solid cone angle from 10L to 10R and from 10U to 5D. 60.2.3. Minimum angles of light distribution referred to the reference axis 60.2.3.1. Vertical: from 10o above to 5o below the horizontal. 60.2.3.2. Horizontal: from 10o to the left to 10o to the right. 60.2.4. Other Requirements Each lamp must:- 60.2.4.1. have an effective projected luminous area not less than 29 square centimetres; 60.2.4.2. not contain symbols, letters or characters other than those necessary for part number, manufacturer's identification and/or approval number identification; 60.2.4.3. provide access for convenient replacement of the globe without the use of special tools; 60.2.4.4. provide a steady warning light; 60.2.4.5. except as provided in clauses 60.2.1 to 60.2.4.2, be designed to conform to the relevant requirements of clauses 1 to 3 of SAE document J186a, September, 1977 "Supplemental High Mounted Stop and Rear Turn Signal Lamps", except that: 60.2.4.5.1. Table 1 of that SAE document is replaced by the light distribution table of clause 60.3.1; 60.2.4.5.2. lamps designed solely for mounting inside the vehicle need not meet the requirements of paragraphs 3.1.6 Moisture Test; 3.1.7 Dust Test; and 3.1.8 Corrosion Test of that SAE document. 60.3. LIGHT TABLES 60.3.1. Table of Minimum Light Distribution (in candela, for degrees of angle) 10U 8 16 8 5U 16 25 25 25 16 V 16 25 25 25 16 5D 16 25 25 25 16 10L 5L H 5R 10R 60.3.2. Colour of light trichromatic co-ordinates 60.3.2.1. Red: limit towards yellow: y < 0.335 limit towards purple: z < 0.008 60.3.2.2. For verifying the limits above, a source of light at a colour temperature of 2856K (illuminant A of the International Commission of Illumination (CIE)), in combination with appropriate filters, may be used. PART II INSTALLATION 60.4. SPECIFICATION 60.4.1. Presence Mandatory. 60.4.2. Number One. 60.4.3. Arrangement No special requirement. 60.4.4. Position 60.4.4.1. In width: on the vehicle's median longitudinal plane. 60.4.4.2. In height: at any position including on the glazing, except that no portion of the lens must be lower than the bottom edge of the rear window by more than: 60.4.4.2.1. 152 mm for convertibles; 60.4.4.2.2. 77 mm for other vehicles. 60.4.5. Geometric visibility 60.4.5.1. The reference axis of the lamp when fitted to the vehicle must be parallel to the bearing plane of the vehicle on the road and lie in the median longitudinal plane of the vehicle. 60.4.5.1.1. Vertical: from 10o above to 5o below the horizontal. 60.4.5.1.2. Horizontal: from 10o to the left to 10o to the right. 60.4.6. Orientation Rearwards. 60.4.7. May not be "grouped" with any other lamp. 60.4.8. May not be "combined" with any other lamp or reflective device. 60.4.9. May not be "reciprocally incorporated" with any other lamp. 60.4.10. Electrical Operation shall be activated upon and only upon application of the service brakes. 60.4.11. Tell-tale Optional. 60.4.12. Other requirements If the lamp is mounted inside the vehicle, it must be shrouded to the glass or other means must be provided to minimise reflections from the light of the lamp upon the rear window glazing that might be visible to the driver when viewed directly, or indirectly, in the rear vision mirror. 60.5. ALTERNATIVE STANDARDS 60.5.1. The technical requirements of FMVSS 108 "Lamps, reflective devices, and associated equipment" or "High-mounted Stop Lamp" are deemed to be equivalent to the technical requirements of this rule. 60.5.2. The technical requirements of Category S3 stop lamps of United Nations Regulation 7/02 read with supplement 2 to the 02 series of amendments and installed in accordance with United Nations Regulation 48/01. COMPILATION NOTES This compilation of Vehicle Standard (Australian Design Rule 60/00 – Centre High Mounted Stop Lamp) 2006 includes all the instruments set out in the Table of Instruments. This vehicle standard is determined under section 12 of the Road Vehicle Standards Act 2018. The Table of Amendments provides a history of clauses that have been amended, inserted or deleted. Table of Instruments Name of Instrument Registration Date Commencement Date Vehicle Standard (Australian Design Rule 1/00 – Reversing lamp) 2006 (F2006L02300) 05/07/2006 05/07/2006 Vehicle Standard (Australian Design Rule) Lighting Standards Amendment Instrument 2022 (No.1) (F2023L00042) 19/01/2023 20/01/2023 Table of Amendments Clause affected How affected Amending instrument A.2. del Legislation Act 2003 – section 48D A.3. del Legislation Act 2003 – section 48C C.2. am Vehicle Standard (Australian Design Rule) Lighting Standards Amendment Instrument 2022 (No.1) 60.5.2. am Vehicle Standard (Australian Design Rule) Lighting Standards Amendment Instrument 2022 (No.1) ad = added or inserted am = amended del = deleted or removed rr = removed and replaced  = clause renumbered. This takes the format of old no.  new no. [*] The category code may also be in the format L1, LA etc.